درایو Yaskawa

Yaskawa بزرگترین تولید کننده درایوهای AC و محصولات کنترل حرکت، از جمله درایوهای فرکانس قابل تنظیم در جهان است.
شرکت هوگر خدمات دهنده درایوهای فعلی و قدیمی و تمامی محصولات یاسکاوا در ایران می باشد.

- درایوهای AC صنعتی
- درایوهای HVAC
- درایوهای پمپ تخصصی
- درایوهای آسانسوری
- درایوهای ولتاژ متوسط
- معرفی یاسکاوا

از سال 1915، Yaskawa Electric نیازهای جهان را برای محصولات برای بهبود بهره وری جهانی از طریق اتوماسیون برآورده کرده است. Yaskawa طیف گسترده ای از درایوهای AC صنعتی از جمله درایوهای عمومی، میکرودرایوها و درایوهای فن و پمپ را تولید می کند. هر کدام عملکرد خاصی را ارائه می دهند که برای کنترل انواع مختلف موتورها طراحی شده است. Yaskawa همچنین درایوهای اجزای آسانسور و درایوهای پمپ ویژه و همچنین درایوهای HVAC با فرکانس متغیر را ارائه می دهد.

انواع درایو

درایوهای همه منظوره

یک درایو عمومی در پمپ ها، فن ها و نوار نقاله ها استفاده می شود. برای نصب و برنامه نویسی ساده و شرایطی که نیازی به مهندسی سفارشی ندارند توصیه می شود. درایوهای هدف عمومی به راحتی تنظیم و کار می کنند و چندین ویژگی داخلی را ارائه می دهند.

درایوهای خاص صنعت

Yaskawa درایوهایی را برای صنایع خاص تولید می کند:
- آبیاری
- ایستگاه های تقویت کننده/بالابر
- سیستم های زمین گرمایی
- کارخانه های فرآیند نمک زدایی
- پمپ های توربین گریز از مرکز و عمودی
- آب های زیرزمینی و فاضلاب
درایوهای Yaskawa برای عملکرد بهینه عملکرد و کاهش انرژی طراحی شده اند.
شرکت هوگر تجربه در تعمیر، سرویس و پشتیبانی درایو Yaskawa را دارد.

خرابی های رایج درایو

درایو موتور را روشن نمی کند
- درایو مدام فیوزها را میپراند یا قطع کننده ها را خاموش می کند
- فن های خنک کننده کار نمیکنند
- مشکلات نرم افزاری یا برنامه نویسی
- خرابی برد مدار

فرآیند تعمیر

ما درایو موتور و پایانه‌ها را برای اتصالات نامرغوب بررسی می‌کنیم که می‌تواند ناشی از هر چیزی از چرخه‌های حرارتی و لرزش مکانیکی گرفته تا استفاده مجدد یا سفت کردن بیش از حد پیچ‌های گشتاور باشد.

ما آزمایش‌های دیود و IGBT را روی بخش‌های توان ورودی/خروجی قبل از اعمال برق به واحد درایو انجام می‌دهیم. این برای محافظت در برابر آسیب بیشتر ناشی از اتصال کوتاه است. دستگاه را روشن می کنیم و آمپر و تست فرکانس خروجی را انجام می دهیم و به آرامی ولتاژ را افزایش می دهیم تا به ولتاژ ورودی نامی درایو برسد. اگر همه چیز به درستی کار کند، پس از پشتیبان گیری از برنامه های موجود، از درایو استفاده می کنیم تا موتور را از طریق توابع پایه اجرا کنیم. اگر موتور کار نمی کند، ولتاژهای خروجی و رتبه های جریانی که به موتور می رود را بررسی می کنیم تا عملکرد درایو را برای چرخش موتور بررسی کنیم.

اکثر خرابی های درایو را می توان از طریق تعمیر و نگهداری پیشگیرانه اجتناب کرد.
شرکت هوگر خدمات و پشتیبانی Yaskawa را ارائه می دهد. برای اطلاعات بیشتر با ما تماس بگیرید.

تعمیرات Yaskawa, درایو Yaskawa

A.020 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.020
Display	Name	Cause	Investigative Actions	Corrective Actions
A.020	Parameter Checksum Error 1(The parameter data in the SERVOPACK is incorrect.)	The power supply voltage suddenly dropped.	Measure the power supply voltage.	Set the power supply voltage within the specified range, and set Fn005 to initialize the parameter.
The power supply went OFF while changing a parameter setting.	The number of times that parameters were written exceeded the limit	Malfunction caused by noise from the AC power supply or grounding line, static electricity noise, etc.
The number of times that parameters were written exceeded the limit.	Check to see if the parameters were frequently changed through the host controller.	The SERVOPACK may be faulty. Repair or replace the SERVOPACK. Reconsider the method of writing parameters.
Malfunction caused by noise from the AC power supply or grounding line, static electricity noise, etc.	Turn the power supply ON and OFF several times. If the alarm still occurs, there may be noise interference.	Take countermeasures against noise.
Gas, water drops, or cutting oil entered the SERVOPACK and caused failure of the internal components.	Check the installation conditions.	The SERVOPACK may be faulty. Replace the SERVOPACK.
A SERVOPACK fault occurred.	Turn the power supply ON and OFF several times. If the alarm still occurs, the SERVOPACK may be faulty.	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.021 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.021
Display	Name	Cause	Investigative Actions	Corrective Actions
A.021	Parameter Format Error 1 (The parameter data in the SERVOPACK is incorrect.)	The software version of SERVOPACK that caused the alarm is older than that of the written parameter.	Check Fn012 to see if the set software version agrees with that of the SERVOPACK. If not, an alarm may occur.	Write the parameter of another SERVOPACK of the same model with the same software version. Then turn the power OFF and then ON again.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.022 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.022
Display	Name	Cause	Investigative Actions	Corrective Actions
A.021	System Checksum Error 1 (The parameter data in the SERVOPACK is incorrect.)	The power supply voltage suddenly dropped.	Measure the power supply voltage.	The SERVOPACK may be faulty. Replace the SERVOPACK.
The power supply went OFF while setting an utility function.	Check the circumstances when the power supply went OFF.	The SERVOPACK may be faulty. Replace the SERVOPACK.
A SERVOPACK fault occurred.	Turn the power supply ON and OFF several times. If the alarm still occurs, the SERVOPACK may be faulty.	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.030 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.030
Display	Name	Cause	Investigative Actions	Corrective Actions
A.030	Main Circuit Detector Error	A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.040 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.040
Display	Name	Cause	Investigative Actions	Corrective Actions
A.040	Parameter Setting Error 1 (The parameter setting was out of the setting range.)	The SERVOPACK and servomotor capacities do not match each other.	Check the combination of SERVOPACK and servomotor capacities.	Select the proper combination of SERVOPACK and servomotor capacities.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.
The parameter setting is out of the setting range.	Check the setting ranges of the parameters that have been changed.	Set the parameter to a value within the setting range.Set the parameter to a value within the setting range.
The electronic gear ratio is out of the setting range.	Check the electronic gear ratio.The ratio must satisfy: 0.001< (Pn20E/Pn210) < 4000.	Set the electronic gear ratio in the range: 0.001< (Pn20E/Pn210) < 4000.

A.041 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.041
Display	Name	Cause	Investigative Actions	Corrective Actions
A.041	Encoder Output Pulse Setting Error	The encoder output pulse (Pn212) is out of the setting range and does not satisfy the setting conditions.	Check the parameter Pn212.	Set Pn212 to a correct value.

A.042 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.042
Display	Name	Cause	Investigative Actions	Corrective Actions
A.042	Parameter Combination Error	The speed of program JOG operation (Fn004) is lower than the setting range after having changed the electronic gear ratio (Pn20E/Pn210) or the servomotor.	Check that the detection conditions are satisfied.	Decrease the setting of the electronic gear ratio (Pn20E/Pn210).
The speed of program JOG operation (Fn004) is lower than the setting range after having changed the setting of the program JOG movement speed (Pn533).	Check that the detection conditions are satisfied.	Increase the setting of the program JOG movement speed (Pn533).
The moving speed of advanced autotuning is lower than the setting range after having changed the electronic gear ratio (Pn20E/Pn210) or the servomotor.	Check that the detection conditions are satisfied.	Decrease the setting of the electronic gear ratio (Pn20E/Pn210).

A.044 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.044
Display	Name	Cause	Investigative Actions	Corrective Actions
A.044	Semi-closed/Fullyclosed Loop Control Parameter Setting Error	The setting of the fully-closed module does not match with that of Pn002.3.	Check the settings of Pn002.3.	The setting of fully-closed module must be compatible with the setting of Pn002.3.

A.050 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.050
Display	Name	Cause	Investigative Actions	Corrective Actions
A.050	Combination Error (The SERVOPACK and servomotor capacities do not correspond.)	The SERVOPACK and servomotor capacities do not match each other.	Check the capacities to see if they satisfy the following condition: 1/4 <= (Servomotor capacity)/(SERVOPACK capacity) <=4.	Select the proper combination of SERVOPACK and servomotor capacities.
An encoder fault occurred.	Replace the servomotor and see if the alarm occurs again.	Replace the servomotor (encoder).
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.051 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.051
Display	Name	Cause	Investigative Actions	Corrective Actions
A.051	Unsupported Device Alarm	An unsupported serial converter unit, encoder, or external encoder is connected to the SERVOPACK.	Check the product specifications, and select the correct model.	Select the correct combination of units.

A.0b0 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.0b0
Display	Name	Cause	Investigative Actions	Corrective Actions
A.0b0	Cancelled Servo ON Command Alarm	After executing the utility function to turn ON the power to the motor, the servo ON signal (/SON) was sent from an external device.	--	Turn the SERVOPACK power supply OFF and then ON again or execute a software reset.

A.100 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.100
Display	Name	Cause	Investigative Actions	Corrective Actions
A.100	Overcurrent or Heat Sink Overheated (An overcurrent flowed through the IGBT or heat sink of SERVOPACK overheated.)	Incorrect wiring or contact fault of main circuit cable or servomotor main circuit cable.	Check the wiring.	Correct the wiring.
Short-circuit or ground fault of main circuit cable or servomotor main circuit cable.	Check for short-circuits across the servomotor terminal phases U, V, and W, or between the grounding and servomotor terminal phases U, V, or W.	The cable may be short-circuited. Replace the cable.
Short-circuit or ground fault inside the servomotor.	Check for short-circuits across the servomotor terminal phases U, V, and W, or between the grounding and servomotor terminal phases U, V, or W.	The servomotor may be faulty. Replace the servomotor.
Short-circuit or ground fault inside the SERVOPACK.	Check for short-circuits across the servomotor connection terminals U, V, and W on the SERVOPACK, or between the grounding and terminal U, V, or W.	The SERVOPACK may be faulty. Replace the SERVOPACK.
Incorrect wiring or contact fault of the regenerative resistor.	Check the wiring.	Correct the wiring.
The dynamic brake (DB: Emergency stop executed from the SERVOPACK) was frequently activated, or the DB overload alarm occurred.	Check the power consumed by DB resistance (Un00B) to see how many times the DB has been used. Or, check the alarm history display Fn000 to see if the DB overload alarm A.730 or A.731 was reported.	Change the SERVOPACK model, operating conditions, or the mechanism so that the DB does not need to be used so frequently.
The generated regenerative resistor value exceeded the SERVOPACK regenerative energy processing capacity.	Check the regenerative load ratio (Un00A) to see how many times the regenerative resistor has been used.	Check the operating condition including overload, and reconsider the regenerative resistor value.
The SERVOPACK regenerative resistance is too small.	Check the regenerative load ratio (Un00A) to see how many times the regenerative resistor has been used.	Change the regenerative resistance value to a value larger than the SERVOPACK minimum allowable resistance value.
A heavy load was applied while the servomotor was stopped or running at a low speed.	Check to see if the operating conditions are outside servo drive specifications.	Reduce the load applied to the servomotor or increase the operating speed.
Malfunction caused by noise interference.	Improve the wiring or installation environment, such as by reducing noise, and check to see if the alarm recurs.	Take countermeasures for noise, such as correct wiring of the FG. Use an FG wire size equivalent to the SERVOPACK main circuit wire size.
A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.300 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.300
Display	Name	Cause	Investigative Actions	Corrective Actions
A.300	Regeneration Error	- Regenerative resistor capacity (Pn600) is set to a value other than 0 for a SGDV- R70, -R90, -1R6, -2R1, or -2R8 SERVOPACK, and an external regenerative resistor is not connected. - An external regenerative resistor is not connected to the SGDV-470, SGDV-550, SGDV-590, SGDV-780, SGDV-210, SGDV- 260, SGDV-280, or SGDV-370 SERVOPACK.	Check the external regenerative resistor connection and the value of the Pn600.	Connect the external regenerative resistor, or set Pn600 to 0 if no regenerative resistor is required.
The jumper between the power supply terminals B2 and B3 is removed.	Confirm that a jumper is mounted between the power supply terminals B2 and B3.	Correctly mount a jumper.
The external regenerative resistor is incorrectly wired, or is removed or disconnected.	Check the external regenerative resistor connection.	Correctly connect the external regenerative resistor.
A SERVOPACK fault occurred.	--	While the main circuit power supply is OFF, turn the control power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.320 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.320
Display	Name	Cause	Investigative Actions	Corrective Actions
A.320	Regenerative Overload	The power supply voltage exceeds the specified limit.	Measure the power supply voltage.	Set the power supply voltage within the specifiedrange.
Insufficient external regenerative resistance, regenerative resistor capacity, or SERVOPACK capacity. Or, regenerative power has been continuously flowing back.	Check the operating condition or the capacity using the capacity selection Software SigmaJunma- Size+, etc.	Change the regenerative resistance, regenerative resistor capacity, or SERVOPACK capacity. Reconsider the operating conditions using the capacity selection software Sigma-JunmaSize+, etc.
Regenerative power continuously flowed back because negative load was continuously applied.	Check the load applied to the servomotor during operation.	Reconsider the system including servo, machine, and operating conditions.
The setting of parameter Pn600 is smaller than the external regenerative resistor's capacity.	Check the external regenerative resistor connection and the value of the Pn600.	Set the Pn600 to a correct value.
The external regenerative resistance is too high.	Check the regenerative resistance.	Change the regenerative resistance to a correct value or use an external regenerative resistor of appropriate capacity.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.330 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.330
Display	Name	Cause	Investigative Actions	Corrective Actions
A.330	Main Circuit Power Supply Wiring Error (Detected when the power to the main circuit is turned ON.)	The regenerative resistor disconnected when the SERVOPACK power supply voltage was high.	Measure the resistance of the regenerative resistor using a measuring instrument.	When using a regenerative resistor built in the SERVOPACK: Replace the SERVOPACK. When using an external regenerative resistor: Replace the external regenerative resistor.
In the AC power input mode, DC power was supplied.	Check the power supply to see if it is a DC power supply.	Correct the settings to match the actual power supply specifications.
In the DC power input mode, AC power was supplied.	Check the power supply to see if it is an AC power supply.	Correct the settings to match the actual power supply specifications.
Regenerative resistor capacity (Pn600) is not set to 0 even though the regenerative resistor is disconnected.	Check if regenerative resistor is connected and check the regenerative resistor capacity	Set Pn600 to 0.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.400 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.400
Display	Name	Cause	Investigative Actions	Corrective Actions
A.400	Overvoltage (Detected in the SERVOPACK main circuit power supply section.)	. For 100-VAC SERVOPACKs: The AC power supply voltage exceeded 145 V.For 200-VAC SERVOPACKs: The AC power supply voltage exceeded 290 V.For 400-VAC SERVOPACKs: The AC power supply voltage exceeded 580 V.For 200-VAC SERVOPACKs: with DC power supply input: The DC power supply voltage exceeded 410 V.For 400 VAC SERVOPACKs: The DC power supply voltage exceeded 820 V.	Measure the power supply voltage.	Set AC/DC power supply voltage within the specified range.
The power supply is unstable, or was influenced by a lightning surge.	Measure the power supply voltage.	Improve the power supply conditions by installing a surge absorber, etc. Then, turn the power supply OFF and ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.
Acceleration/deceleration was executed under the following conditions. The AC power supply voltage of 100-VAC SERVOPACK was in the range between 115 V and 135 V. The AC power supply voltage of 200-VAC SERVOPACK was in the range between 230 V and 270 V. The AC power supply voltage of 400-VAC SERVOPACK was in the range between 480 V and 560 V.	Check the power supply voltage and the speed and torque during operation.	Set AC power supply voltage within the specified range.
The external regenerative resistance is too high for the actual operating conditions.	Check the operating conditions and the regenerative resistance.	Select a regenerative resistance value appropriate for the operating conditions and load.
The moment of inertia ratio exceeded the allowable value.	Confirm that the moment of inertia ratio is within the allowable range.	Increase the deceleration time, or reduce the load.
A SERVOPACK fault occurred.	--	Turn the control power OFF and then ON again while the main circuit power supply is OFF. Replace the SERVOPACK.

A.410 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.410
Display	Name	Cause	Investigative Actions	Corrective Actions
A.410	Undervoltage (Detected in the SERVOPACK main circuit power supply section.)	. For 100-VAC SERVOPACKs: The AC power supply voltage is 49 V or less. . For 200-VAC SERVOPACKs: The AC power supply voltage is 120 V or less. . For 400-VAC SERVOPACKs: The AC power supply voltage is 240 V or less.	Measure the power supply voltage.	Set the power supply voltage within the specified range.
The power supply voltage dropped during operation.	Measure the power supply voltage.	Increase the power supply capacity.
Occurrence of instantaneous power interruption.	Measure the power supply voltage.	When the instantaneous power cut hold time (Pn509) is set, decrease the setting.
The SERVOPACK fuse is blown out.	--	Replace the SERVOPACK, connect a reactor, and run the SERVOPACK.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.450 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.450
Display	Name	Cause	Investigative Actions	Corrective Actions
A.450	Main-Circuit Capacitor Overvoltage	A SERVOPACK fault occurred.	--	Replace the SERVOPACK.

A.450 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.510
Display	Name	Cause	Investigative Actions	Corrective Actions
A.510	Overspeed (The servomotor rotational speed exceeds the maximum.)	The order of phases U, V, and W in the servomotor wiring is incorrect.	Check the servomotor wiring.	Confirm that the servomotor is correctly wired.
A reference value exceeding the overspeed detection level was input.	Check the input value.	Reduce the reference value or adjust the gain.
The motor speed exceeded the maximum.	Check the servomotor speed waveform.	Reduce the speed reference input gain, adjust the servo gain, or reconsider the operating conditions.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.511 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.511
Display	Name	Cause	Investigative Actions	Corrective Actions
A.511	Overspeed of Encoder Output Pulse Rate	The encoder output pulse frequency exceeded the limit.	Check the encoder output pulse setting.	Decrease the setting of the encoder output pulse (Pn212).
The encoder output pulse output frequency exceeded the limit because the servomotor speed was too high.	Check the encoder output pulse output setting and servomotor speed.	Decrease the servomotor speed.

A.520 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.520
Display	Name	Cause	Investigative Actions	Corrective Actions
A.520	Vibration Alarm	Abnormal vibration was detected at the servomotor speed.	Check for abnormal noise from the servomotor, and check the speed and torque waveforms during operation.	Reduce the servomotor speed or reduce the speed loop gain (Pn100).
The moment of inertia ratio (Pn103) value is greater than the actual value or is greatly changed.	Check the moment of inertia ratio.	Set the moment of inertia ratio (Pn103) to an appropriate value.

A.521 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.521
Display	Name	Cause	Investigative Actions	Corrective Actions
A.521	Autotuning Alarm (Vibration was detected while executing the advanced autotuning, one-parameter tuning, EasyFFT, or tuning-less function.)	The servomotor vibrated considerably while performing tuningless function (factory setting).	Check the servomotor speed waveform.	Reduce the load so that the moment of inertia ratio falls within the allowable value, or raise the tuning level using the tuning-less levels setting (Fn200) or reduce the load level.
The servomotor vibrated considerably during advanced autotuning, one- parameter tuning, or EasyFFT.	Check the servomotor speed waveform.	Check the operation procedure of corresponding function and take a corrective action.

A.710 - A.720 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.710 - A.720
Display	Name	Cause	Investigative Actions	Corrective Actions
A.710 A.720 - Overload A.710 - High Load A.720 - Low Load	Incorrect wiring or contact fault of servomotor and encoder.	Check the wiring.	Confirm that the servomotor and encoder are correctly wired.
Operation beyond the overload protection characteristics.	Check the servomotor overload characteristics and executed run command.	Reconsider the load conditions and operating conditions. Or, increase the servomotor capacity.
Excessive load was applied during operation because the servomotor was not driven due to mechanical problems.	Check the executed operation reference and servomotor speed.	Remove the mechanical problems.
A SERVOPACK fault occurred./td>	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.730 - A.731 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.730 - A.731
Display	Name	Cause	Investigative Actions	Corrective Actions
A.730 A.731	Dynamic Brake Overload (An excessive power consumption of dynamic brake was detected.)	The servomotor rotates because of external force.	Check the operation status.	Take measures to ensure the servomotor will not rotate because of external force.
The rotating energy at a DB stop exceeds the DB resistance capacity.	Check the power consumed by DB resistance (Un00B) to see how many times the DB has been used.	Reconsider the following: . Reduce the servomotor reference speed. . Reduce the moment of inertia ratio. . Reduce the number of times of the DB stop operation.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.740 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.740
Display	Name	Cause	Investigative Actions	Corrective Actions
A.740	Overload of Surge Current Limit Resistor (The main circuit power is turned ON/OFF too frequently.)	The inrush current limit resistor operation frequency at the main circuit power supply ON/OFF operation exceeds the allowable range.	--	Reduce the frequency of turning the main circuit power supply ON/OFF.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.7A0 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.7A0
Display	Name	Cause	Investigative Actions	Corrective Actions
A.7A0	Heat Sink Overheated (Detected when the heat sink temperature exceeds 100°C.)	The surrounding air temperature is too high.	Check the surrounding air temperature using a thermostat.	Decrease the surrounding air temperature by improving the SERVOPACK installation conditions.
The overload alarm has been reset by turning OFF the power too many times.	Check the alarm history display (Fn000) to see if the overload alarm was reported.	Change the method for resetting the alarm.
Excessive load or operation beyond the regenerative energy processing capacity.	Check the accumulated load ratio (Un009) to see the load during operation, and the regenerative load ratio (Un00A) to see the regenerative energy processing capacity.	Reconsider the load and operating conditions.
Incorrect SERVOPACK installation orientation or/and insufficient space around the SERVOPACK.	Check the SERVOPACK installation conditions.	Install the SERVOPACK correctly as specified.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.7AB لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.7AB
Display	Name	Cause	Investigative Actions	Corrective Actions
A.7AB	Built-in Fan in SERVOPACK Stopped	The fan inside the SERVOPACK stopped.	Check for foreign matter or debris inside the SERVOPACK.	Remove foreign matter or debris from the SERVOPACK. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.810 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.810
Display	Name	Cause	Investigative Actions	Corrective Actions
A.810	Encoder Backup Error (Only when an absolute encoder is connected.) (Detected on the encoder side.)	Alarm occurred when the power to the absolute encoder was initially turned ON.	Check to see if the power was turned ON initially.	Set up the encoder (Fn008).
The encoder cable disconnected, and connected again.	Check to see if the power was turned ON initially.	Confirm the connection and set up the encoder (Fn008).
The power from both the control power supply (+5 V) from the SERVOPACK and the battery power supply is not being supplied	Check the encoder connector battery or the connector contact status.	Replace the battery or take similar measures to supply power to the encoder, and set up the encoder (Fn008).
An absolute encoder fault occurred.	--	If the alarm cannot be reset by setting up the encoder again, replace the servomotor.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.820 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.820
Display	Name	Cause	Investigative Actions	Corrective Actions
A.820	Encoder Checksum Error (Detected on the encoder side.)	An encoder fault occurred.	--	Set up the encoder again using Fn008. If the alarm still occurs, the servomotor may be faulty. Replace the servomotor.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.830 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.830
Display	Name	Cause	Investigative Actions	Corrective Actions
A.830	Absolute Encoder Battery Error (The absolute encoder battery voltage is lower than the specified value.)	The battery connection is incorrect.	Check the battery connection.	Reconnect the battery.
The battery voltage is lower than the specified value 2.7V.	Measure the battery voltage.	Replace the battery.
A SERVOPACK fault occurred.	--	The SERVOPACK may be faulty. Replace the SERVOPACK.

A.840 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.840
Display	Name	Cause	Investigative Actions	Corrective Actions
A.840	Encoder Data Error (Detected on the encoder side.)	The encoder malfunctioned.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the servomotor may be faulty. Replace the servomotor.
Malfunction of encoder because of noise interference, etc.	--	Correct the wiring around the encoder by separating the encoder cable from the servomotor main circuit cable or by checking the grounding and other wiring.

A.850 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.850
Display	Name	Cause	Investigative Actions	Corrective Actions
A.850	Encoder Overspeed (Detected when the control power supply was turned ON.) (Detected on the encoderside.)	The servomotor was running at 200 min- 1 or higher when the control power supply was turned ON.	Check the motor rotating speed (Un000) to confirm the servomotor speed when the power is turned ON.	Reduce the servomotor speed to a value less than 200 min-1, and turn ON the control power supply.
An encoder fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the servomotor may be faulty. Replace the servomotor.
A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.860 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.860
Display	Name	Cause	Investigative Actions	Corrective Actions
A.860	Encoder Overheated (Only when an absolute encoder is connected.) (Detected on the encoder side.)	The ambient operating temperature around the servomotor is too high.	Measure the ambient operating temperature around the servomotor.	The ambient operating temperature must be 40°C or less.
The servomotor load is greater than the rated load.	Check the accumulated load ratio (Un009) to see the load.	The servomotor load must be within the specified range.
An encoder fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the servomotor may be faulty. Replace the servomotor.
A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.8A0 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.8A0
Display	Name	Cause	Investigative Actions	Corrective Actions
A.8A0	External Encoder Error	Setting the zero point position of external absolute encoder failed because the servomotor rotated. Before setting the zero point	position, use the fully-closed feedback pulse counter (Un00E) to confirm that the servomotor is not rotating.	The servomotor must be stopped while setting the zero point position.
An external encoder fault occurred.	--	Replace the external encoder.

A.8A1 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.8A1
Display	Name	Cause	Investigative Actions	Corrective Actions
A.8A1	External Encoder Error of Module	An external encoder fault occurred.	--	Replace the external encoder.
A serial converter unit fault occurred.	--	Replace the serial converter unit.

A.8A لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.8A
Display	Name	Cause	Investigative Actions	Corrective Actions
A.8A	External Encoder Error of Sensor (Incremental)	An external encoder fault occurred.	--	Replace the external encoder.

A.8A3 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.8A3
Display	Name	Cause	Investigative Actions	Corrective Actions
A.8A3	External Encoder Error of Position (Absolute)	An external absolute encoder fault occurred.	--	The external absolute encoder may be faulty. Refer to the encoder manufacturer's instruction manual for corrective actions.

A.8A5 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.8A5
Display	Name	Cause	Investigative Actions	Corrective Actions
A.8A5	External Encoder	Overspeed The overspeed from the external	encoder occurred. Check the maximum speed of the	external encoder. Keep the external encoder below its maximum speed.

A.8A6 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.8A6
Display	Name	Cause	Investigative Actions	Corrective Actions
A.8A6	External Encoder Overheated	The overheat from the external encoder occurred.	--	Repair or replace the external encoder.

A.b10 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.b10
Display	Name	Cause	Investigative Actions	Corrective Actions
A.b10	Speed Reference A/D Error	(Detected when the servo is ON.) A malfunction occurred in the speed	reference input section.	-- Clear and reset the alarm and restart the operation.
A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.b11 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.b11
Display	Name	Cause	Investigative Actions	Corrective Actions
A.b11	Speed Reference A/D Data Error A malfunction occurred in the speed	reference input section.	--	Clear and reset the alarm and restart the operation.
A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.b20 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.b20
Display	Name	Cause	Investigative Actions	Corrective Actions
A.b20	Reference Torque Input Read Error (Detected when the servo is ON.)	A malfunction occurred in the reading section of the torque reference input.	--	Clear and reset the alarm and restart the operation.
A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.b31 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.b31
Display	Name	Cause	Investigative Actions	Corrective Actions
A.b31	Current Detection Error 1	The current detection circuit for phase U is faulty.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.b32 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.b32
Display	Name	Cause	Investigative Actions	Corrective Actions
A.b32	Current Detection Error 2	The current detection circuit for phase V is faulty.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.b33 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.b33
Display	Name	Cause	Investigative Actions	Corrective Actions
A.b33	Current Detection Error 3	The detection circuit for the current is faulty.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.
The servomotor main circuit cable is disconnected.	Check for disconnection of the servomotor main circuit cable.	Correct the servomotor wiring.

A.bF0 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.bF0
Display	Name	Cause	Investigative Actions	Corrective Actions
A.bF0	System Alarm 0	A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.bF1 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.bF1
Display	Name	Cause	Investigative Actions	Corrective Actions
A.bF1	System Alarm 1	A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.bF2 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.bF2
Display	Name	Cause	Investigative Actions	Corrective Actions
A.bF2	System Alarm 2	A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.bF3 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.bF3
Display	Name	Cause	Investigative Actions	Corrective Actions
A.bF3	System Alarm 3	A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

A.bF4 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.bF4
Display	Name	Cause	Investigative Actions	Corrective Actions
A.bF4	System Alarm 4	A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Model	V	Kw	A
Yaskawa frequency inverters GA700 general purpose series
3 phase 200-240 V, capacity from 0,55 kW to 110 kW (HD) 3 phase 200-240 V, capacity from 0,75 kW to 110 kW (ND) 3 phase 380-480 V, capacity from 0,55 kW to 315 kW (HD) 3 phase 380-480 V, capacity from 0,75 kW to 355 kW (ND)
CIPR-GA70C2004BA	200-240 (3ph)	0,55	3.2
CIPR-GA70C2006BA	200-240 (3ph)	0,75	5
CIPR-GA70C2010BA	200-240 (3ph)	1,5	8
CIPR-GA70C2012BA	200-240 (3ph)	2,2	11
CIPR-GA70C2018BA	200-240 (3ph)	3	14
CIPR-GA70C2021BA	200-240 (3ph)	4	17.5
CIPR-GA70C2030BA	200-240 (3ph)	5,5	25
CIPR-GA70C2042BA	200-240 (3ph)	7,5	33
CIPR-GA70C2056BA	200-240 (3ph)	11	47
CIPR-GA70C2070BA	200-240 (3ph)	15	60
CIPR-GA70C2082BA	200-240 (3ph)	18,5	75
CIPR-GA70C2110BA	200-240 (3ph)	22	88
CIPR-GA70C2138BA	200-240 (3ph)	30	115
CIPR-GA70C2169BA	200-240 (3ph)	37	145
CIPR-GA70C2211BA	200-240 (3ph)	45	180
CIPR-GA70C2257BA	200-240 (3ph)	55	215
CIPR-GA70C2313BA	200-240 (3ph)	75	283
CIPR-GA70C2360BA	200-240 (3ph)	90	346
CIPR-GA70C2415BA	200-240 (3ph)	110	415
CIPR-GA70C2004BA	200-240 (3ph)	0,75	3.5
CIPR-GA70C2006BA	200-240 (3ph)	1,1	6
CIPR-GA70C2010BA	200-240 (3ph)	2,2	9.6
CIPR-GA70C2012BA	200-240 (3ph)	3	12.2
CIPR-GA70C2018BA	200-240 (3ph)	4	17.5
CIPR-GA70C2021BA	200-240 (3ph)	5,5	21
CIPR-GA70C2030BA	200-240 (3ph)	7,5	30
CIPR-GA70C2042BA	200-240 (3ph)	11	42
CIPR-GA70C2056BA	200-240 (3ph)	15	56
CIPR-GA70C2070BA	200-240 (3ph)	18,5	70
CIPR-GA70C2082BA	200-240 (3ph)	22	82
CIPR-GA70C2110BA	200-240 (3ph)	30	110
CIPR-GA70C2138BA	200-240 (3ph)	37	138
CIPR-GA70C2169BA	200-240 (3ph)	45	169
CIPR-GA70C2211BA	200-240 (3ph)	55	211
CIPR-GA70C2257BA	200-240 (3ph)	75	257
CIPR-GA70C2313BA	200-240 (3ph)	90	313
CIPR-GA70C2360BA	200-240 (3ph)	110	360
CIPR-GA70C4002BA	380-480 (3ph)	0,55	1.8
CIPR-GA70C4004BA	380-480 (3ph)	0,75	3.4
CIPR-GA70C4005BA	380-480 (3ph)	1,5	4.8
CIPR-GA70C4007BA	380-480 (3ph)	2,2	5.5
CIPR-GA70C4009BA	380-480 (3ph)	3	7.2
CIPR-GA70C4012BA	380-480 (3ph)	3,7	9.2
CIPR-GA70C4018BA	380-480 (3ph)	5,5	14.8
CIPR-GA70C4023BA	380-480 (3ph)	7,5	18
CIPR-GA70C4031BA	380-480 (3ph)	11	24
CIPR-GA70C4038BA	380-480 (3ph)	15	31
CIPR-GA70C4044BA	380-480 (3ph)	18,5	39
CIPR-GA70C4060BA	380-480 (3ph)	22	45
CIPR-GA70C4075BA	380-480 (3ph)	30	60
CIPR-GA70C4089BA	380-480 (3ph)	37	75
CIPR-GA70C4103BA	380-480 (3ph)	45	91
CIPR-GA70C4140BA	380-480 (3ph)	55	112
CIPR-GA70C4168BA	380-480 (3ph)	75	150
CIPR-GA70C4208BA	380-480 (3ph)	90	180
CIPR-GA70C4250BA	380-480 (3ph)	110	216
CIPR-GA70C4296BA	380-480 (3ph)	132	260
CIPR-GA70C4371BA	380-480 (3ph)	160	304
CIPR-GA70C4389BA	380-480 (3ph)	200	371
CIPR-GA70C4453BA	380-480 (3ph)	220	414
CIPR-GA70C4568BA	380-480 (3ph)	250	453
CIPR-GA70C4675BA	380-480 (3ph)	315	605
CIPR-GA70C4002BA	380-480 (3ph)	0,75	2.1
CIPR-GA70C4004BA	380-480 (3ph)	1,5	4.1
CIPR-GA70C4005BA	380-480 (3ph)	2,2	5.4
CIPR-GA70C4007BA	380-480 (3ph)	3	7.1
CIPR-GA70C4009BA	380-480 (3ph)	3,7	8.9
CIPR-GA70C4012BA	380-480 (3ph)	5,5	11.9
CIPR-GA70C4018BA	380-480 (3ph)	7,5	17.5
CIPR-GA70C4023BA	380-480 (3ph)	11	23.4
CIPR-GA70C4031BA	380-480 (3ph)	15	31
CIPR-GA70C4038BA	380-480 (3ph)	18,5	38
CIPR-GA70C4044BA	380-480 (3ph)	22	44
CIPR-GA70C4060BA	380-480 (3ph)	30	59.6
CIPR-GA70C4075BA	380-480 (3ph)	37	74.9
CIPR-GA70C4089BA	380-480 (3ph)	45	89.2
CIPR-GA70C4103BA	380-480 (3ph)	55	103
CIPR-GA70C4140BA	380-480 (3ph)	75	140
CIPR-GA70C4168BA	380-480 (3ph)	90	168
CIPR-GA70C4208BA	380-480 (3ph)	110	208
CIPR-GA70C4250BA	380-480 (3ph)	132	250
CIPR-GA70C4296BA	380-480 (3ph)	160	296
CIPR-GA70C4371BA	380-480 (3ph)	200	371
CIPR-GA70C4389BA	380-480 (3ph)	220	389
CIPR-GA70C4453BA	380-480 (3ph)	250	453
CIPR-GA70C4568BA	380-480 (3ph)	315	568
CIPR-GA70C4675BA	380-480 (3ph)	355	675

Repair, Yaskawa, Inverters, GA700

Display	Name	Cause	Investigative Actions	Corrective Actions
A.C10 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.C10
A.C10	Servo Overrun Detected (Detected when the servomotor power is ON.)	The order of phases U, V, and W in the servomotor wiring is incorrect.	Check the servomotor wiring.	Confirm that the servomotor is correctly wired.
		An encoder fault occurred.	--	If the alarm still occurs after turning the power OFF and then ON again, even though the servomotor is correctly wired, the servomotor may be faulty. Replace the servomotor.
		A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK

Display	Name	Cause	Investigative Actions	Corrective Actions
A.C80 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.C80
A.C80	Absolute Encoder Clear Error and Multiturn Limit Setting Error	An encoder fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the servomotor may be faulty. Replace the servomotor.
A.C80		A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.C90 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.C90
A.C90	Encoder Communications Error	Contact fault of encoder connector or incorrect encoder wiring.	Check the encoder connector contact status.	Re-insert the encoder connector and confirm that the encoder is correctly wired.
		Encoder cable disconnection or short- circuit. Or, incorrect cable impedance.	Check the encoder cable.	Use the encoder cable with the specified rating.
		Corrosion caused by improper temperature, humidity, or gas, short- circuit caused by intrusion of water drops or cutting oil, or connector contact fault caused by vibration.	Check the operating environment.	Improve the operating environmental conditions, and replace the cable. If the alarm still occurs, replace the SERVOPACK.
		Malfunction caused by noise interference.	--	Correct the wiring around the encoder to avoid noise interference (Separate the encoder cable from the servomotor main circuit cable, improve grounding, etc.)
		A SERVOPACK fault occurred.	--	Connect the servomotor to another SERVOPACK, and turn ON the control power. If no alarm occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.C91 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.C91
A.C91	Encoder Communications Position Data Error	The noise interference occurred on the I/O signal line because the encoder cable is bent and the sheath is damaged.	Check the encoder cable and connector.	Confirm that there is no problem with the encoder cable layout.
		The encoder cable is bundled with a high current line or near a high-current line.	Check the encoder cable layout.	Confirm that there is no surge voltage on the encoder cable.
		The FG potential varies because of influence from machines on the servomotor side, such as the welder.	Check the encoder cable layout.	Properly ground the machines to separate from the encoder FG.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.C92 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.C92
A.C92	Encoder Communications Timer Error	Noise interference occurred on the I/O signal line from the encoder.	--	Take countermeasures against noise for the encoder wiring.
		Excessive vibration and shocks were applied to the encoder.	Check the operating environment.	Reduce the machine vibration or correctly install the servomotor.
		An encoder fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the servomotor may be faulty. Replace the servomotor.
		A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.CA0 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.CA0
A.CA0	Encoder Parameter Error	An encoder fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the servomotor may be faulty. Replace the servomotor.
A.CA0	Encoder Parameter Error	A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.CB0 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.CB0
A.CB0	Encoder Echoback Error	The encoder wiring and contact are incorrect.	Check the encoder wiring.	Correct the encoder wiring.
		Noise interference occurred due to incorrect encoder cable specifications.	--	Use tinned annealed copper shielded twisted-pair or screened unshielded twisted-pair cable with a core of at least 0.12 mm2.
		Noise interference occurred because the wiring distance for the encoder cable is too long.	--	The wiring distance must be 50 m max.
		The FG potential varies because of influence from machines on the servomotor side, such as the welder.	Check the encoder cable layout.	Properly ground the machines to separate from encoder FG.
		Excessive vibration and shocks were applied to the encoder.	Check the operating environment.	Reduce the machine vibration or correctly install the servomotor.
		An encoder fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the servomotor may be faulty. Replace the servomotor.
		A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.CC0 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.CC0
A.CC0	Multiturn Limit Disagreement	When using a direct drive (DD) servo motor, the multiturn limit value (Pn205) is different from that of the encoder.	Check the value of the Pn205.	Correct the setting of Pn205 (0 to 65535).
		The multiturn limit value of the encoder is different from that of the SERVOPACK. Or, the multiturn limit value of the SERVOPACK has been changed.	Check the value of the Pn205 of the SERVOPACK.	Execute Fn013 at the occurrence of alarm.
		A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.CF1 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.CF1
A.CF1	Feedback Option Module Communications Error (Reception error)	Wiring of cable between serial converter unit and SERVOPACK is incorrect or contact is faulty.	Check the external encoder wiring.	Correct the cable wiring.
		The specified cable is not used between serial converter unit and SERVOPACK.	Confirm the external encoder wiring specifications.	Use the specified cable.
		Cable between serial converter unit and SERVOPACK is too long.	Measure the length of this cable.	Use 20-m cable max.
		Sheath of cable between serial converter unit and SERVOPACK is broken.	Check the cable for damage.	Replace the cable.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.CF2 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.CF2
A.CF2	Feedback Option Module Communications Error (Timer stop)	Noise interferes with the cable between serial converter unit and SERVOPACK.	--	Correct the wiring around serial converter unit, e.g., separating I/O signal line from main circuit cable or grounding.
		A serial converter unit fault occurred.	--	Replace the serial converter unit.
		A SERVOPACK fault occurred.	--	Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.d00 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.d00
A.d00	Position Error Overflow (Position error exceeded the value set in the excessive position error alarm level (Pn520).)	The servomotor U, V, and W wirings is faulty.	Check the servomotor main circuit cable connection.	Confirm that there is no contact fault in the motor wiring or encoder wiring.
		The frequency of the position reference pulse is too high.	Reduce the reference pulse frequency, and operate the SERVOPACK.	Reduce the position reference pulse frequency or acceleration of position reference. Or, reconsider the electronic gear ratio.
		The position reference acceleration is too fast.	Reduce the reference acceleration, and operate the SERVOPACK.	Apply the smoothing function, such as using position reference acceleration/deceleration time constant (Pn216).
		Setting of the excessive position error alarm level (Pn520) is low against the operating condition.	Check the alarm level (Pn520) to see if it is set to an appropriate value.	Set the Pn520 to proper value.
		A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.d01 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.d01
A.d01	Position Error Overflow Alarm at Servo ON	This alarm occurs if the servo ON signal (/S-ON) is turned ON when the position error is greater than the set value of Pn526.	Check the position error amount (Un008) while the /S-ON signal is OFF.	Set position error to be cleared while the /S-ON signal is OFF. Or, correct the excessive position error alarm level at servo ON (Pn526).

Display	Name	Cause	Investigative Actions	Corrective Actions
A.d02 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.d02
A.d02	Position Error Overflow Alarm by Speed Limit at Servo ON	When pulses remain in the error counter, Pn529 limits the speed if the /S- ON signal is turned ON. If Pn529 limits the speed in such a state, this alarm occurs when reference pulses are input and the number of position errors exceeds the value set for the excessive position error alarm level (Pn520).	--	Set position error to be cleared while the /S-ON signal is OFF. Or, correct the excessive position error alarm level (Pn520). Or, adjust the speed limit level at servo ON (Pn529).

Display	Name	Cause	Investigative Actions	Corrective Actions
A.d10 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.d10
A.d10	Motor-load Position Error Overflow	Motor rotation direction and external encoder installation direction are opposite.	Check the servomotor rotation direction and the external encoder installation direction.	Install the external encoder in the opposite direction, or change the setting of the external encoder usage method (Pn002.3) to reverse the direction.
A.d10	Motor-load Position Error Overflow	Mounting of the load (e.g., stage) and external encoder joint installation are incorrect.	Check the external encoder mechanical connection.	Check the mechanical joints.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.E72 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.E72
A.E72	Feedback Option Module Detection Failure	The connection between the SERVOPACK and the Feedback Option Module is Faulty.	Check the connection between the SERVOPACK and the Feedback Option Module.	Correctly connect the Feedback Option Module.
		The Feedback Option Module was disconnected.	--	Execute resetting configuration error in option modules (Fn014) and turn the power supply OFF and then ON again.
		A Feedback Option Module fault	--	Replace the Feedback Option Module.
		A SERVOPACK fault occurred.	--	Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.Eb1 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.Eb1
A.Eb1	Safety Function Signal Input Timing Error	The lag between activations of the input signals /HWBB1 and /HWBB2 for the HWBB function is ten second or more.	Measure the time lag between the /HWBB1 and /HWBB2 signals.	The output signal circuits or devices for /HWBB1 and /HWBB2 or the SERVOPACK input signal circuits may be faulty. Alternatively, the input signal cables may be disconnected. Check if any of these items are faulty or have been disconnected.

Display	Name	Cause	Investigative Actions	Corrective Actions
A.F10 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - A.F10
A.F10	Main Circuit Cable Open Phase (With the main power supply ON, voltage was low for more than 1 second in an R, S, or T phase.) (Detected when the main power supply was turned ON.)	The three-phase power supply wiring is incorrect.	Check the power supply wiring.	Confirm that the power supply is correctly wired.
		The three-phase power supply is unbalanced.	Measure the voltage at each phase of the three-phase power supply.	Balance the power supply by changing phases.
		A single-phase power is input without setting Pn00B.2 (power supply method for three-phase SERVOPACK) to 1 (single- phase power supply).	Check the power supply and the parameter setting.	Match the parameter setting to the power supply.
		A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Display	Name	Cause	Investigative Actions	Corrective Actions
CPF00 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - CPF00
CPF00	Digital Operator Transmission Error 1	The contact between the digital operator and the SERVOPACK is faulty.	Check the connector contact.	Insert securely the connector or replace the cable.
CPF00	Digital Operator Transmission Error 1	Malfunction caused by noise interference.	--	Keep the digital operator or the cable away from noise sources.

Display	Name	Cause	Investigative Actions	Corrective Actions
CPF01 لیست ارور اینورترهای یاسکاوا
Drive Error List - Yaskawa - CPF01
CPF01	Digital Operator Transmission Error 2	A digital operator fault occurred.	--	Disconnect the digital operator and then re- connect it. If the alarm still occurs, the digital operator may be faulty. Replace the digital operator.
CPF01	Digital Operator Transmission Error 2	A SERVOPACK fault occurred.	--	Turn the power supply OFF and then ON again. If the alarm still occurs, the SERVOPACK may be faulty. Replace the SERVOPACK.

Model	V	Kw	A
Yaskawa frequency inverters J1000 compact series
200V (1 phase), capacity range: 0.4kW - 2.2kW (ND) 200V (1 phase), capacity range: 0.2kW - 1.5kW (HD) 400V (3 phase), capacity range: 0.4kW - 5.5kW (ND) 400V (3 phase), capacity range: 0.2kW - 4.0kW (HD)
CIMR-JCBA0002BAA	200 (1ph)	0,4	1.9
CIMR-JCBA0003BAA	200 (1ph)	0,75	3.5
CIMR-JCBA0006BAA	200 (1ph)	1,1	6
CIMR-JCBA0010BAA	200 (1ph)	2,2	9.6
CIMR-JC4A0001BAA	400 (3ph)	0,4	1.2
CIMR-JC4A0002BAA	400 (3ph)	0,75	2.1
CIMR-JC4A0004BAA	400 (3ph)	1,5	4.1
CIMR-JC4A0005BAA	400 (3ph)	2,2	5.4
CIMR-JC4A0007BAA	400 (3ph)	3	6.9
CIMR-JC4A0009BAA	400 (3ph)	3,7	8.8
CIMR-JC4A0011BAA	400 (3ph)	5,5	11.1

Model	V	Kw	A
Yaskawa frequency inverters V1000 compact series
200V (1 phase), capacity range: 0.1kW - 4.0kW (HD) 400V (1 phase), capacity range: 0.4kW - 5.5kW (ND) 400V (1 phase), capacity range: 0.2kW - 4.0kW (HD) 400V (3 phase), capacity range: 7.5kW - 18.5kW (ND) 400V (3 phase), capacity range: 5.5kW - 15.0kW (HD)
CIMR-VCBA0001BAA	200 (1ph)	0,2	1.2
CIMR-VCBA0002BAA	200 (1ph)	0,4	1.9
CIMR-VCBA0003BAA	200 (1ph)	0,75	3.3
CIMR-VCBA0006BAA	200 (1ph)	1,1	6
CIMR-VCBA0010BAA	200 (1ph)	2,2	9.6
CIMR-VCBA0012BAA	200 (1ph)	3	12
CIMR-VCBA0018BAA	200 (1ph)	4	17.5
CIMR-VCBA0001HAA-0080	200 (1ph)	0,2	1.2
CIMR-VCBA0002HAA-0080	200 (1ph)	0,4	1.9
CIMR-VCBA0003HAA-0080	200 (1ph)	0,75	3.3
CIMR-VCBA0006HAA-0080	200 (1ph)	1,1	6
CIMR-VCBA0010HAA-0080	200 (1ph)	2,2	9.6
CIMR-VCBA0012HAA-0080	200 (1ph)	3	12
CIMR-VCBA0001HAA-0081	200 (1ph)	0,2	1.2
CIMR-VCBA0002HAA-0081	200 (1ph)	0,4	1.9
CIMR-VCBA0003HAA-0081	200 (1ph)	0,75	3.3
CIMR-VCBA0006HAA-0081	200 (1ph)	1,1	6
CIMR-VCBA0010HAA-0081	200 (1ph)	2,2	9.6
CIMR-VCBA0012HAA-0081	200 (1ph)	3	12
CIMR-VC4A0001HAA-0080	400 (1ph)	0,4	1.2
CIMR-VC4A0002HAA-0080	400 (1ph)	0,75	2.1
CIMR-VC4A0004HAA-0080	400 (1ph)	1,5	4.1
CIMR-VC4A0005HAA-0080	400 (1ph)	2,2	5.4
CIMR-VC4A0007HAA-0080	400 (1ph)	3	6.9
CIMR-VC4A0009HAA-0080	400 (1ph)	3,7	8.8
CIMR-VC4A0011HAA-0080	400 (3ph)	5,5	11.1
CIMR-VC4A0001HAA-0081	400 (1ph)	0,4	1.2
CIMR-VC4A0002HAA-0081	400 (1ph)	0,75	2.1
CIMR-VC4A0004HAA-0081	400 (1ph)	1,5	4.1
CIMR-VC4A0005HAA-0081	400 (1ph)	2,2	5.4
CIMR-VC4A0007HAA-0081	400 (1ph)	3	6.9
CIMR-VC4A0009HAA-0081	400 (1ph)	3,7	8.8
CIMR-VC4A0010HAA-0081	400 (1ph)	5,5	11.1
CIMR-VC4A0018HAA-0080	400 (3ph)	7,5	17.1
CIMR-VC4A0023HAA-0080	400 (3ph)	11	23
CIMR-VC4A0031HAA-0080	400 (3ph)	15	31
CIMR-VC4A0038HAA-0080	400 (3ph)	18,5	38
CIMR-VC4A0018HAA-0081	400 (3ph)	7,5	17.1
CIMR-VC4A0023HAA-0081	400 (3ph)	11	23
CIMR-VC4A0031HAA-0081	400 (3ph)	15	31
CIMR-VC4A0038HAA-0081	400 (3ph)	18,5	38
CIMR-VC4A0001ВAA	400 (3ph)	0,4	1.2
CIMR-VC4A0002ВAA	400 (3ph)	0,75	2.1
CIMR-VC4A0004ВAA	400 (3ph)	1,5	4.1
CIMR-VC4A0005ВAA	400 (3ph)	2,2	5.4
CIMR-VC4A0007ВAA	400 (3ph)	3	6.9
CIMR-VC4A0009ВAA	400 (3ph)	3,7	8.8
CIMR-VC4A0011ВAA	400 (3ph)	5,5	11.1
CIMR-VC4A0018FAA	400 (3ph)	7,5	17.5
CIMR-VC4A0023FAA	400 (3ph)	11	23
CIMR-VC4A0031FAA	400 (3ph)	15	31
CIMR-VC4A0038FAA	400 (3ph)	18,5	38

Model	V	Kw	A
Yaskawa frequency inverters A1000 general purpose series
400V (3 phase), capacity range: 0.75kW - 630kW (ND) 400V (3 phase), capacity range: 0.55kW - 560kW (HD)
CIMR-AC4A0044TAA-0095	400 (3ph)	18,5	39
CIMR-AC4A0058TAA-0095	400 (3ph)	22	45
CIMR-AC4A0072TAA-0095	400 (3ph)	30	60
CIMR-AC4A0088TAA-0095	400 (3ph)	37	75
CIMR-AC4A0103TAA-0095	400 (3ph)	45	91
CIMR-AC4A0139TAA-0095	400 (3ph)	55	112
CIMR-AC4A0165TAA-0095	400 (3ph)	75	150
CIMR-AC4A0044WAA	400 (3ph)	18,5	39
CIMR-AC4A0058WAA	400 (3ph)	22	45
CIMR-AC4A0072WAA	400 (3ph)	30	60
CIMR-AC4A0088WAA	400 (3ph)	37	75
CIMR-AC4A0103WAA	400 (3ph)	45	91
CIMR-AC4A0139WAA	400 (3ph)	55	112
CIMR-AC4A0165WAA	400 (3ph)	75	150
CIMR-AC4A0044TAA	400 (3ph)	18,5	39
CIMR-AC4A0058TAA	400 (3ph)	22	45
CIMR-AC4A0072TAA	400 (3ph)	30	60
CIMR-AC4A0088TAA	400 (3ph)	37	75
CIMR-AC4A0103TAA	400 (3ph)	45	91
CIMR-AC4A0139TAA	400 (3ph)	55	112
CIMR-AC4A0165TAA	400 (3ph)	75	150
CIMR-AC4A0002FAA	400 (3ph)	0,75	2.1
CIMR-AC4A0004FAA	400 (3ph)	1,5	4.1
CIMR-AC4A0005FAA	400 (3ph)	2,2	5.4
CIMR-AC4A0007FAA	400 (3ph)	3	6.9
CIMR-AC4A0009FAA	400 (3ph)	4	8.8
CIMR-AC4A0011FAA	400 (3ph)	5,5	11.1
CIMR-AC4A0018FAA	400 (3ph)	7,5	17.5
CIMR-AC4A0023FAA	400 (3ph)	11	23
CIMR-AC4A0031FAA	400 (3ph)	15	31
CIMR-AC4A0038FAA	400 (3ph)	18,5	38
CIMR-AC4A0044FAA	400 (3ph)	22	44
CIMR-AC4A0058AAA	400 (3ph)	30	58
CIMR-AC4A0072AAA	400 (3ph)	37	72
CIMR-AC4A0088AAA	400 (3ph)	45	88
CIMR-AC4A0103AAA	400 (3ph)	55	103
CIMR-AC4A0139AAA	400 (3ph)	75	139
CIMR-AC4A0165AAA	400 (3ph)	90	165
CIMR-AC4A0208AAA	400 (3ph)	110	208
CIMR-AC4A0250AAA	400 (3ph)	132	250
CIMR-AC4A0296AAA	400 (3ph)	160	296
CIMR-AC4A0362AAA	400 (3ph)	185	362
CIMR-AC4A0414AAA	400 (3ph)	220	414
CIMR-AC4A0515AAA	400 (3ph)	250	515
CIMR-AC4A0675AAA	400 (3ph)	355	675
CIMR-AC4A0930AAA	400 (3ph)	500	930
CIMR-AC4A1200AAA	400 (3ph)	630	1200

Model	V	Kw	A
Yaskawa frequency inverters U1000 compact series
200V (3 phase), capacity range: 7.5kW - 75.0kW 400V (3 phase), capacity range: 5.5kW - 260kW
CIMR-UC2A0028A	200 (3ph)	7,5	28
CIMR-UC2A0042A	200 (3ph)	11	42
CIMR-UC2A0054A	200 (3ph)	15	54
CIMR-UC2A0068A	200 (3ph)	18,5	68
CIMR-UC2A0081A	200 (3ph)	22	81
CIMR-UC2A0104A	200 (3ph)	30	104
CIMR-UC2A0130A	200 (3ph)	37	130
CIMR-UC2A0154A	200 (3ph)	45	154
CIMR-UC2A0192A	200 (3ph)	55	192
CIMR-UC2A0248A	200 (3ph)	75	248
CIMR-UC4A0011A	380-480 (3ph)	5,5	11
CIMR-UC4A0014A	380-480 (3ph)	7,5	14
CIMR-UC4A0021A	380-480 (3ph)	11	21
CIMR-UC4A0027A	380-480 (3ph)	15	27
CIMR-UC4A0034A	380-480 (3ph)	18,5	34
CIMR-UC4A0040A	380-480 (3ph)	22	40
CIMR-UC4A0052A	380-480 (3ph)	30	52
CIMR-UC4A0065A	380-480 (3ph)	37	65
CIMR-UC4A0077A	380-480 (3ph)	45	77
CIMR-UC4A0096A	380-480 (3ph)	55	96
CIMR-UC4A0124A	380-480 (3ph)	75	124
CIMR-UC4A0156A	380-480 (3ph)	90	156
CIMR-UC4A0180A	380-480 (3ph)	110	180
CIMR-UC4A0216A	380-480 (3ph)	132	216
CIMR-UC4A0240A	380-480 (3ph)	150	240
CIMR-UC4A0302A	380-480 (3ph)	185	302
CIMR-UC4A0361A	380-480 (3ph)	220	361
CIMR-UC4A0414A	380-480 (3ph)	260	414

Model	V	Kw	A
Yaskawa frequency inverters P1000 series for pump application
200V (3 phase), capacity range: 0.75kW - 110kW 400V (3 phase), capacity range: 0.75kW - 355kW
CIMR-PU2A0004	200-240 (3ph)	0,75	3.5
CIMR-PU2A0006	200-240 (3ph)	1,1	6
CIMR-PU2A0008	200-240 (3ph)	1,5	8
CIMR-PU2A0010	200-240 (3ph)	2,2	9.6
CIMR-PU2A0012	200-240 (3ph)	3	12
CIMR-PU2A0018	200-240 (3ph)	3,7	17.5
CIMR-PU2A0021	200-240 (3ph)	5,5	21
CIMR-PU2A0030	200-240 (3ph)	7,5	30
CIMR-PU2A0040	200-240 (3ph)	11	40
CIMR-PU2A0056	200-240 (3ph)	15	56
CIMR-PU2A0069	200-240 (3ph)	18,5	69
CIMR-PU2A0081	200-240 (3ph)	22	81
CIMR-PU2A0110	200-240 (3ph)	30	110
CIMR-PU2A0138	200-240 (3ph)	37	138
CIMR-PU2A0169	200-240 (3ph)	45	169
CIMR-PU2A0211	200-240 (3ph)	55	211
CIMR-PU2A0250	200-240 (3ph)	75	250
CIMR-PU2A0312	200-240 (3ph)	90	312
CIMR-PU2A0360	200-240 (3ph)	110	360
CIMR-PU2A0415	200-240 (3ph)	110	415
CIMR-PU4A0002	380-480 (3ph)	0,75	2.1
CIMR-PU4A0004	380-480 (3ph)	1,5	4.1
CIMR-PU4A0005	380-480 (3ph)	2,2	5.4
CIMR-PU4A0007	380-480 (3ph)	3	6.9
CIMR-PU4A0009	380-480 (3ph)	3,7	8.8
CIMR-PU4A0011	380-480 (3ph)	5,5	11.1
CIMR-PU4A0018	380-480 (3ph)	7,5	17.5
CIMR-PU4A0023	380-480 (3ph)	11	23
CIMR-PU4A0031	380-480 (3ph)	15	31
CIMR-PU4A0038	380-480 (3ph)	18,5	38
CIMR-PU4A0044	380-480 (3ph)	22	44
CIMR-PU4A0058	380-480 (3ph)	30	58
CIMR-PU4A0072	380-480 (3ph)	37	72
CIMR-PU4A0088	380-480 (3ph)	45	88
CIMR-PU4A0103	380-480 (3ph)	55	103
CIMR-PU4A0139	380-480 (3ph)	75	139
CIMR-PU4A0165	380-480 (3ph)	90	165
CIMR-PU4A0208	380-480 (3ph)	110	208
CIMR-PU4A0250	380-480 (3ph)	132	250
CIMR-PU4A0296	380-480 (3ph)	160	296
CIMR-PU4A0362	380-480 (3ph)	185	362
CIMR-PU4A0414	380-480 (3ph)	220	414
CIMR-PU4A0515	380-480 (3ph)	250	515
CIMR-PU4A0675	380-480 (3ph)	355	675

Model	V	Kw	A
Yaskawa frequency inverters L1000A lift series
3 phase 200-240 V, capacity from 1,5 kW to 110 kW 3 phase 380-480 V, capacity from 1,5 kW to 110 kW
CIMR-LC2A0008	200-240 (3ph)	1,5	8
CIMR-LC2A0011	200-240 (3ph)	2,2	11
CIMR-LC2A0018	200-240 (3ph)	4	18
CIMR-LC2A0025	200-240 (3ph)	5,5	25
CIMR-LC2A0033	200-240 (3ph)	7,5	33
CIMR-LC2A0047	200-240 (3ph)	11	47
CIMR-LC2A0060	200-240 (3ph)	15	60
CIMR-LC2A0075	200-240 (3ph)	18,5	75
CIMR-LC2A0085	200-240 (3ph)	22	85
CIMR-LC2A0115	200-240 (3ph)	30	115
CIMR-LC2A0145	200-240 (3ph)	37	145
CIMR-LC2A0180	200-240 (3ph)	45	180
CIMR-LC2A0215	200-240 (3ph)	55	215
CIMR-LC2A0283	200-240 (3ph)	75	283
CIMR-LC2A0346	200-240 (3ph)	90	346
CIMR-LC2A0415	200-240 (3ph)	110	415
CIMR-LC4F0005	380-480 (3ph)	1,5	5
CIMR-LC4F0006	380-480 (3ph)	2,2	6
CIMR-LC4F0009	380-480 (3ph)	4	9
CIMR-LC4F0015	380-480 (3ph)	5,5	15
CIMR-LC4F0018	380-480 (3ph)	7,5	18
CIMR-LC4F0024	380-480 (3ph)	11	24
CIMR-LC4F0031	380-480 (3ph)	15	31
CIMR-LC4F0039	380-480 (3ph)	18,5	39
CIMR-LC4F0045	380-480 (3ph)	22	45
CIMR-LC4F0060	380-480 (3ph)	30	60
CIMR-LC4F0075	380-480 (3ph)	37	75
CIMR-LC4F0091	380-480 (3ph)	45	91
CIMR-LC4F0112	380-480 (3ph)	55	112
CIMR-LC4F0150	380-480 (3ph)	75	150
CIMR-LC4F0180	380-480 (3ph)	90	180
CIMR-LC4F0216	380-480 (3ph)	110	216

Model	V	Kw	A
Yaskawa frequency inverters L1000V lift series
3 phase 200-240 V, capacity from 5,5 kW to 15 kW 3 phase 380-480 V, capacity from 4 kW to 15 kW
CIMR-LC2V0025	200-240 (3ph)	5,5	25
CIMR-LC2V0033	200-240 (3ph)	7,5	33
CIMR-LC2V0047	200-240 (3ph)	11	47
CIMR-LC2V0060	200-240 (3ph)	15	60
CIMR-LC4V0009	380-480 (3ph)	4	9.2
CIMR-LC4V0015	380-480 (3ph)	5,5	14.8
CIMR-LC4V0018	380-480 (3ph)	7,5	18
CIMR-LC4V0024	380-480 (3ph)	11	24
CIMR-LC4V0031	380-480 (3ph)	15	31

Model	V	Kw	A
Yaskawa frequency inverters T1000V machinery series
1 phase 200-240 V, capacity from 0,1 kW to 3 kW 3 phase 200-240 V, capacity from 0,1 kW to 18,5 kW 3 phase 380-480 V, capacity from 0,2 kW to 18,5 kW
CIMR-TCBV0001	200-240 (1ph)	0,2	1.2
CIMR-TCBV0002	200-240 (1ph)	0,4	1.9
CIMR-TCBV0003	200-240 (1ph)	0,75	3.5
CIMR-TCBV0006	200-240 (1ph)	1,1	6
CIMR-TCBV0010	200-240 (1ph)	2,2	9.6
CIMR-TCBV0012	200-240 (1ph)	3	12
CIMR-TCBV0001	200-240 (1ph)	0,1	0.8
CIMR-TCBV0002	200-240 (1ph)	0,2	1.6
CIMR-TCBV0003	200-240 (1ph)	0,4	3
CIMR-TCBV0006	200-240 (1ph)	0,75	5
CIMR-TCBV0010	200-240 (1ph)	1,5	8
CIMR-TCBV0012	200-240 (1ph)	2,2	11
CIMR-TC2V0001	200-240 (3ph)	0,2	1.2
CIMR-TC2V0002	200-240 (3ph)	0,4	1.9
CIMR-TC2V0004	200-240 (3ph)	0,75	3.5
CIMR-TC2V0006	200-240 (3ph)	1,1	6
CIMR-TC2V0010	200-240 (3ph)	2,2	9.6
CIMR-TC2V0012	200-240 (3ph)	3	12
CIMR-TC2V0020	200-240 (3ph)	5,5	19.6
CIMR-TC2V0030	200-240 (3ph)	7,5	30
CIMR-TC2V0040	200-240 (3ph)	11	40
CIMR-TC2V0056	200-240 (3ph)	15	56
CIMR-TC2V0069	200-240 (3ph)	18,5	69
CIMR-TC2V0001	200-240 (3ph)	0,1	0.8
CIMR-TC2V0002	200-240 (3ph)	0,2	1.6
CIMR-TC2V0004	200-240 (3ph)	0,4	3
CIMR-TC2V0006	200-240 (3ph)	0,75	5
CIMR-TC2V0010	200-240 (3ph)	1,5	8
CIMR-TC2V0012	200-240 (3ph)	2,2	11
CIMR-TC2V0020	200-240 (3ph)	4	17.5
CIMR-TC2V0030	200-240 (3ph)	5,5	25
CIMR-TC2V0040	200-240 (3ph)	7,5	33
CIMR-TC2V0056	200-240 (3ph)	11	47
CIMR-TC2V0069	200-240 (3ph)	15	60
CIMR-TC4V0001	380-480 (3ph)	0,4	1.2
CIMR-TC4V0002	380-480 (3ph)	0,75	2.1
CIMR-TC4V0004	380-480 (3ph)	1,5	4.1
CIMR-TC4V0005	380-480 (3ph)	2,2	5.4
CIMR-TC4V0007	380-480 (3ph)	3	6.9
CIMR-TC4V0009	380-480 (3ph)	4	8.8
CIMR-TC4V0011	380-480 (3ph)	5,5	11.1
CIMR-TC4V0018	380-480 (3ph)	7,5	17.5
CIMR-TC4V0023	380-480 (3ph)	11	23
CIMR-TC4V0031	380-480 (3ph)	15	31
CIMR-TC4V0038	380-480 (3ph)	18,5	38
CIMR-TC4V0001	380-380 (3ph)	0,2	1.2
CIMR-TC4V0002	380-480 (3ph)	0,4	1.8
CIMR-TC4V0004	380-480 (3ph)	0,75	3.4
CIMR-TC4V0005	380-480 (3ph)	1,5	4.8
CIMR-TC4V0007	380-480 (3ph)	2,2	5.5
CIMR-TC4V0009	380-480 (3ph)	3	7.2
CIMR-TC4V0011	380-480 (3ph)	4	9.2
CIMR-TC4V0018	380-480 (3ph)	5,5	14.8
CIMR-TC4V0023	380-480 (3ph)	7,5	18
CIMR-TC4V0031	380-480 (3ph)	11	24
CIMR-TC4V0038	380-480 (3ph)	15	31

Model	V	Kw	A
Yaskawafrequnecy inverters T1000A series for textile machinery
3 phase 200-240 V, capacity from 0,55 kW to 110 kW 3 phase 380-480 V, capacity from 0,55 kW to 185 kW
CIMR-TC2A0004	200-240 (3ph)	0,75	3.5
CIMR-TC2A0006	200-240 (3ph)	1,1	6
CIMR-TC2A0010	200-240 (3ph)	2,2	9.6
CIMR-TC2A0012	200-240 (3ph)	3	12
CIMR-TC2A0021	200-240 (3ph)	5,5	21
CIMR-TC2A0030	200-240 (3ph)	7,5	30
CIMR-TC2A0040	200-240 (3ph)	11	40
CIMR-TC2A0056	200-240 (3ph)	15	56
CIMR-TC2A0069	200-240 (3ph)	18,5	69
CIMR-TC2A0081	200-240 (3ph)	22	81
CIMR-TC2A0110	200-240 (3ph)	30	110
CIMR-TC2A0138	200-240 (3ph)	37	138
CIMR-TC2A0169	200-240 (3ph)	45	169
CIMR-TC2A0211	200-240 (3ph)	55	211
CIMR-TC2A0250	200-240 (3ph)	75	250
CIMR-TC2A0312	200-240 (3ph)	90	312
CIMR-TC2A0360	200-240 (3ph)	110	360
CIMR-TC2A0415	200-240 (3ph)	110	415
CIMR-TC2A0004	200-240 (3ph)	0,55	3.2
CIMR-TC2A0006	200-240 (3ph)	1,1	5
CIMR-TC2A0010	200-240 (3ph)	1,5	8
CIMR-TC2A0012	200-240 (3ph)	2,2	11
CIMR-TC2A0021	200-240 (3ph)	4	17.5
CIMR-TC2A0030	200-240 (3ph)	5,5	25
CIMR-TC2A0040	200-240 (3ph)	7,5	33
CIMR-TC2A0056	200-240 (3ph)	11	47
CIMR-TC2A0069	200-240 (3ph)	15	60
CIMR-TC2A0081	200-240 (3ph)	18,5	75
CIMR-TC2A0110	200-240 (3ph)	22	85
CIMR-TC2A0138	200-240 (3ph)	30	115
CIMR-TC2A0169	200-240 (3ph)	37	145
CIMR-TC2A0211	200-240 (3ph)	45	180
CIMR-TC2A0250	200-240 (3ph)	55	215
CIMR-TC2A0312	200-240 (3ph)	75	283
CIMR-TC2A0360	200-240 (3ph)	90	346
CIMR-TC2A0415	200-240 (3ph)	110	415
CIMR-TC4A0002	380-480 (3ph)	0,75	2.1
CIMR-TC4A0004	380-480 (3ph)	1,5	4.1
CIMR-TC4A0005	380-480 (3ph)	2,2	5.4
CIMR-TC4A0007	380-480 (3ph)	3	6.9
CIMR-TC4A0009	380-480 (3ph)	3,7	8.8
CIMR-TC4A0011	380-480 (3ph)	5,5	11.1
CIMR-TC4A0018	380-480 (3ph)	7,5	17.5
CIMR-TC4A0023	380-480 (3ph)	11	23
CIMR-TC4A0031	380-480 (3ph)	15	31
CIMR-TC4A0038	380-480 (3ph)	18,5	38
CIMR-TC4A0044	380-480 (3ph)	22	44
CIMR-TC4A0058	380-480 (3ph)	30	58
CIMR-TC4A0072	380-480 (3ph)	37	72
CIMR-TC4A0088	380-480 (3ph)	45	88
CIMR-TC4A0103	380-480 (3ph)	55	103
CIMR-TC4A0139	380-480 (3ph)	75	139
CIMR-TC4A0165	380-480 (3ph)	90	165
CIMR-TC4A0208	380-480 (3ph)	110	208
CIMR-TC4A0250	380-480 (3ph)	132	250
CIMR-TC4A0296	380-480 (3ph)	160	296
CIMR-TC4A0362	380-480 (3ph)	185	362
CIMR-TC4A0002	380-480 (3ph)	0,55	1.8
CIMR-TC4A0004	380-480 (3ph)	1,1	3.4
CIMR-TC4A0005	380-480 (3ph)	1,5	4.8
CIMR-TC4A0007	380-480 (3ph)	2,2	5.5
CIMR-TC4A0009	380-480 (3ph)	3	7.2
CIMR-TC4A0011	380-480 (3ph)	4	9.2
CIMR-TC4A0018	380-480 (3ph)	5,5	14.8
CIMR-TC4A0023	380-480 (3ph)	7,5	18
CIMR-TC4A0031	380-480 (3ph)	11	24
CIMR-TC4A0038	380-480 (3ph)	15	31
CIMR-TC4A0044	380-480 (3ph)	18,5	39
CIMR-TC4A0058	380-480 (3ph)	22	45
CIMR-TC4A0072	380-480 (3ph)	30	60
CIMR-TC4A0088	380-480 (3ph)	37	75
CIMR-TC4A0103	380-480 (3ph)	45	91
CIMR-TC4A0139	380-480 (3ph)	55	112
CIMR-TC4A0165	380-480 (3ph)	75	150
CIMR-TC4A0208	380-480 (3ph)	90	180
CIMR-TC4A0250	380-480 (3ph)	110	216
CIMR-TC4A0296	380-480 (3ph)	132	260
CIMR-TC4A0362	380-480 (3ph)	160	304